Custom Parts Hammer In Hand Custom Cycles Store
aftermarket parts News & Media
Leather Work Photo Gallery
Metal Fab About Us
Service Garage Contact us


All parts listed on this page are not built by Hammer In Hand.

We can order just about anything you need, so if what you want is not listed give Brent a call or send us an email.

You do not need a PayPal account to place an order.


- Frame & Body -



gas tank

Bobber Gas Tank

  • Scalloped sides
  • Tunnel measures 2 1/4" wide, 15" long & 4" deep at front
  • Holds 2.3 gallons
  • Use with 3/8" NPT fuel valve
  • Raw Steel



7 1/2" Wide Steel Flat Trailer Style Fender

  • Cold rolled from 14 gauge steel
  • 48" from end to end from center
  • 29 1/2" gap end to end
  • Raw Steel



6" Wide Hard body Rear Fender

  • Cold rolled from 14 gauge steel
  • Measures a full 48" in circumference, can be cut to length
  • Fender is not drilled or relieved for the chain or drive belt
  • Raw Steel


chrome fender

Chrome Front Fender for FX, FXR & Sportster

  • Fits 35mm front forks on FX, FXR & Sportster models 1973/1987
  • For use with 18", 19" & 21" wheels




Rigid Frame

Fits Panhead, Shovelhead or Big Twin Evo with solid mount engine

  • 1 1/2" O.D. DOM .188" wall tubing for backbone strength
  • 1 1/4" O.D. DOM .120" wall tubing for cradle and tail strength
  • Will accept 4 or 5 Speed transmission
  • Softail style seat front mounting tab


sportster fra e

Ironhead Sportster Rigid Frame

  • 1 1/2" O.D. DOM .188" wall tubing for backbone strength
  • 1 1/4" O.D. DOM .120" wall tubing for cradle and tail strength
  • Wide tire frames accept 180 series tire with chain drive
  • Stock frame accepts 140 tire with chain


neck cup

Neck Cup Conversion Kit

  • K Model & Sportster 1952-1981
  • Includes races and bearings



i" under kickstand

Jiffy Stand for Sportster

  • Fits Ironhead Sportster models 1957/Early 1984 with generator
  • Uses bolt installation instead of pin and screw.



Grate Style Kickstart Pedal

Fits all models Big Twin 1936-1976 and Sportster 1952-1976

  • Heavy Die cast with hardened steel inner core
  • Includes pedal pin busing & wave washer
  • Choose from polished brass (shown) or Chrome


fork boots

Fork Boots

  • Choose fitment of FXST, FXDWG, FXWG (41 mm) or FXD, XL (39 mm)





OE Style Chrome Gas Cap

Fits Harley-Davidson®

  • Vented cap fits single and Fat Bob right hand tanks
  • Non-Vented cap fits Fat Bob left hand tanks
  • Early Model cap shown, both available.



Le Pera Solo Seats

  • Metal flake finish
  • Includes adjustable front mount
  • Steel base
  • Measures 9 1/2" wide x 13" long and 1 1/4" thick
  • Spring mount studs are on 6 1/4" centers



Le Pera Pillion Pads

  • Metal flake finish
  • Carpeted steel base
  • Measures 9" long x 5" wide
  • Mounting holes are threaded 5/16-18 and on 6 3/8" centers


seat hinge

Chrome Custom Seat Springs

  • Bolts to the bottom of solo seats
  • 3"
  • Sold in pairs and two different styles: A and B



seat hinge

Universal Seat Hinge

  • Chromed brackets allow for easy flip access to components
  • Square style fits 52-72 XL, K models and custom rigid and FXST/FLST frames
  • Round style may be used on most custom rigid and softails



- Bars & Controls -


- Back to the list-

D Bars

Chrome Drag Bars

1" OD


z bars

Chrome Z Bars

1 1/4" OD

(1" @ controls & mounting points)



Chrome Risers

Fits any Big Twin or Sportster

  • 1 1/2" pullback and 4 1/2" rise
  • Lets handlebars clear Fat Bob tanks
  • Use 1/2-13 mounting bolts
  • Use with stock screws and clamps



Chrome Universal Round Mirror

  • One piece stem with universal clamp
  • Fits both sides, 7/8" & 1" bars
  • 3" Diameter face


internal throttle

Internal Throttle or Clutch

  • 750" or 800" inside diameter
  • Requires 1" inside diameter grips


  • Note: Due to the throttle sized cable needed for the clutch side, pressure reducing components will be required to actuate the clutch.




Nostalgic Rubber Grips

Fits all models with exterior throttle cables.


White and Red and Black


Throttle Assembly with

Jackhammer Grips

Fits all models with an exterior throttle cable.

(except handlebars with air reservoir)

  • Use with universal throttle cables or 1974/Early 1976 Bendix cable with stock elbow and adjuster.



- Electrical -


- Back to the list-

braided spark plug wire
Click on the image for terminal information

Braided Cloth

Spark Plug Wire


Choose from 3 different colors:

A. Black

B. Red with black/yellow leads

C. Burnt Oak with red/black leads


Comes in 3 Foot lengths

spark plug wires



Vintage Tail Light

  • Drilled lens ring



Titmouse Taillights


  • 1 5/8 Diameter by 1 5/8 long
  • Red dual element cluster covered in stainless steel for an industrial look.
  • Available in aluminum or brass








55/60 Halogen Headlight

  • 12 volt headlight with replaceable H4 type bulb
  • Includes a 5 watt running light for safety and low light
  • Bottom swivel mount with 3/8-24x1" stud with nut
  • Pre-wired with 6" of lead wire
  • Does not include high beam indicator




Brake Light Switch

  • Universal pull type switch
  • Virtually waterproof with enclosed terminals




- Engine -


- Back to the list-


122 pitch 530 STD Diamond Motorcycle Chain

For use with our Straight Back Bolt on Hardtail

For a transmission sprocket from stock (21 tooth) to a 23 tooth.

Click on the image for instructions on ordering custom lengths.




top end gasket set

Top End Gasket Set for Sportster


Seal set includes copper head gaskets

Fits 900cc Ironhead Sportsters, (1973-1976 1000cc) choose your year.




oilfilter adapter


Oil Filter Adapter Kit

Fits Big Twin and Sportster all years

(except Twin Cam)

Black finish




Oil Filter Adapter Kit

Fits Big Twin and Sportster all years

(except Twin Cam)

Chrome finish



Kicker Pedal

Kickstart Conversion Kit

For Big Twin

  • Everything you need to convert electric start to kickstart on all Big Twin models with 4 Speed Transmissions.
  • Kit includes, chrome plated kick arm and chrome plated return spring.



electric start

XLH Electric Start Kits


Include parts pictured to fit 1967-80 XL. Your existing clutch drum must have starter ring gear attached. Side mount electric start oil tank must be purchased when fitted to 1971-80 models. Kick and electric start sprocket cover must be used if kick start is to be retained. Battery, top cover and strap not included. Email or call us if you need any other required parts and we can add them to your order.



Prestolite 1971-78 XLH


Hitachi 1979-80 XLH

heat wrap

Exhaust Insulating Wrap

  • Protects against pipe burns
  • Increases horsepower & fuel efficiency.
  • Withstands temps up to 2000° F



Custom Exhaust

Builders Exhaust Kit

  • 1 3/4" O.D.
  • Four 16" straight sections
  • Two 3.5" radius U-bends with straights
  • Two 5" radius U-bends with straights
  • Two Evolution/Twin cam head flanges
  • Two Shovelhead head flanges
  • Two Ironhead flanges
  • Two Fishtail tips
  • Two Panhead flanges






- Air/Fuel -


- Back to the list-

keihin carb kit

Keihin Carb Rebuild Kit

  • Designed for Keihin Carbs with butterfly type choke

Fits Big Twin 1976-1989 &Sportster Late 1976-1987




bendix rebuild kit

Zenith/Bendix Carb Rebuild Kit

  • Kit includes a three way adjustable accelerator pump.

Fits all 36mm, 38mm and 40mm Bendix/Zenith carburetors.




bendix carb pump

Accelerator Pump Replacement

Fits all Zenith/Bendix carburetors


super E Carb S&S

S&S Cycle Shorty Super E Carburetor Kit

Kit Includes car, intake manifold, carb plate, air filter, chrome air filter housing, fuel lines, vent lines, spare jets, gaskets and O rings, nuts and bolts and instructions.


Find your correct model then choose the year from the drop down list.



XL Sportster

Big Twin Evo


Big Twin Cam

- Misc -


- Back to the list-


Rear Drive Belt for Stock & Wide Tire Use

  • For use with our 1982-2003 Weld on Hard Tail.
  • 139 T @ 1 1/8" Width Belt





Solution Graphics
  • 0/100
  • Should be Empty:

  •   ...
    The Horse Magazine
    Wrench Magazine
    Search Engine
  • Should be Empty: